Damar Septiawan 1 ; Dan Irfan Prasetia 2
1 Megister Civil Engineering Study Program, Faculty of Engineering, Lambung Mangkurat University, South Borneo, Indonesia.
2 Megister Civil Engineering Study Program, Faculty of Engineering, Lambung Mangkurat University, South Borneo, Indonesia.

Article Id - IJCE_04_01_002, Pages : 16-26, Date of Publication : 09, July 2021

7 Downloads   53 Views   0 Citation
Google Scholar Link
Academia Link


In 2019, PT Adaro Indonesia carried out a program of installing aramco culverts with a diameter of 3 meters and construction of gabions at the inlet and outlet sections at Sta 70+200 HW, to replace the function of culvert construction at Sta 70+300 HW which was no longer functioning. well. However, the condition of the aramco culvert installation construction project and gabion construction, as of February 2, 2020, is still in the form of construction progress of 90.62%. Even though the planned target is to start on July 29, 2019 and finish on September 29, 2019. In this project, there are several factors that are thought to affect project delays. This research was conducted to find the real causes of the constraints on the project. This study used a questionnaire and interview instruments. Respondents were selected with the assumption that they had been involved in or worked on a sump and mud drainage installation project. The data is then tested and after being declared valid and reliable then analyzed using the FMEA (Failure Modes and Effects Analysis) method. The results showed that 3 items became the dominant project risk factors, namely the risk of project failure due to changes in planning and specifications (RPN 706.90), Project failure risk due to no project delay penalty (RPN 633.70), Project failure risk due to late delivery of materials to the site (RPN 436.67). Based on the foregoing, further observations and interviews were conducted to obtain mitigation recommendations as a strategy to minimize the potential risk of project failure. The proposed risk mitigation strategy is with careful planning with observations in accordance with actual field conditions, using a professional/competent third party (planning consultant) in planning and design, using the Procrument Road method in the form of Design and Build, a binding contract is enforced between the implementer and the contractor. owner, include in the contract documents related to the penalty scheme that must be accepted by the vendor if the project experiences delays or failures, applies more stock of stone material for gabion work and applies more than 1 river stone supplier selection.


Drainage Installation, Sump Water, Risk Factors, FMEA, Strategy, Mitigation.

Share and Cite:

Damar Septiawan and Dan Irfan Prasetia, Delay Risk Analysis of PT Adaro Indonesia Construction Project - Case Study on PT Adaro Indonesia Tabalong Water and Mud Installation Project, International Journal of Construction Engineering (IJCE), 4(1), 2021, pp. 16-26


[1]    Alifen, R. S., R. S. Setiawan., A. Sunarto. 2000. Analisa “What If” Sebagai Metode Antisipasi Keterlambatan Durasi Proyek, Dimensi Teknik Sipil Vol. 2 No. 1.
[2]    Andi, A., S. Susandi., H. Wijaya. 2003. On Representing Factors Influencing Time Performance Of Shop-House Contructions In Surabaya, Dimensi Teknik Sipil Vol. 5 No. 2
[3]    Assaf, A. 1995. Causes of Delay in Large Building Construction Projects, Journal of Management in Engineering.
[4]    Astina, Dhian C. N., Ida A. R. W., dan I. G. P. Joni. 2012. Analisis Faktor-Faktor Penyebab Keterlambatan Pelaksanaan Pekerjaan Proyek Konstruksi Di Kabupaten Tabanan, Jurnal Ilmiah Elektronik Infrastruktur Teknik Sipil. 
[5]    Bakhtiyar, Ariful., Agoes S., dan M. H. Hasyim. 2012. Analisis Faktor-Faktor Yang Mempengaruhi Keterlambatan Proyek Konstruksi Pembangunan Gedung Di Kota Lamongan, Jurnal Rekayasa Sipil Volume 6, No. 1 – 2012 ISSN 1978 – 5658. 
[6]    Dewi, Dian, A. N. N. D. 2018. Modul Uji Validitas dan Reliabilitas, Diponegoro University, ( quoted on February 16, 2019 at 17.24 WITA).
[7]    Guilford, J. P. (1956). Fundamental Statistics in Psychology and Education. New York: Mc Graw-Hill Book Co. Inc.
[8]    Iin, Hurin. 2017. Manajemen Risiko Teknologi Informasi Pada Proyek Perusahaan Xyz Melalui Kombinasi Cobit, Pmbok, Dan Iso 31000, Tesis, Sepuluh Nopember Institute of Technology, Surabaya.
[9]    Joni, I. G. Putu. 2012. Resiko Manajemen Proyek, Jurnal Ilmiah Teknik Sipil Vol. 16, No. 1. 
[10]    Lestari, I. Indah., dan Toni Mindra. 2019. Analisis Korelasi Rank Spearman Atribut Produk Terhadap Keputusan Pembelian Spare Part di Bengkulu (Survey pada Global Motor Bengkulu), Jurnal Ilmiah Akuntansi, Manajemen & Ekonomi Islam (JAM-Ekis) Volume 18, Nomor 1.
[11]    Murtani. 2017. Analisis Faktor-Faktor Kendala Proyek pada Pembangunan Pelabuhan Swarangan-Pelaihari, Tesis, Universitas Lambung Mangkurat, Banjarmasin.
[12]    Nasution, A. H. 2008. Manajemen Industri, Penerbit Andi, Yogyakarta.
[13]    Pertiwi, Havea. 2017. Implementasi Manajemen Resiko Berdasarkan PMBOK Untuk Mencegah Keterlambatan Proyek Area Jawa Timur (Studi Kasus: PT. Telkom), Jurnal Studi Manajemen dan Bisnis Vol 4 No.02. 
[14]    Proboyo, B. 1999. Keterlambatan Waktu Pelaksanaan Proyek : Klasifikasi Dan Peringkat Dari Penyebab-Penyebabnya, Dimensi Teknik Sipil Vol. 1 No. 2
[15]    Pratama, Dedi., dan Irfan Prasetia. 2019. Prevention Strategy of The Delivery of Construction Projects in Feces Mud Processing Infrastructure Development, American Journal of Engineering Research (AJER) vol.7, no.12, pp. 132-138.
[16]    Sakinah, Baiq Farida. 2015. Analisis Penyebab Keterlambatan pada Pekerjaan Konstruksi Jalan Kabupaten Lombok Tengah dengan Metode Analisa Faktor, Jurnal, Brawijaya University.
[17]    Saputra, Ramdhan Yudndra. 2017. Analisa Faktor Penyebab Keterlambatan Penyelesaian Proyek Pembangunan Mall ABC, Tesis, Sepuluh Nopember Institute of Technology, Surabaya.
[18]    Syarifudin, S. Widodo., dan Arif Nurwaskito. 2017. Kajian Sistem Penyaliran Pada Tambang Terbuka Kabupaten Tanah Bumbu Provinsi Kalimantan Selatan, Jurnal Geomine, Vol. 5, No. 2.
[19]    Widhiasari, Pieta., dan Irfan Prasetia. 2018. Risk Analysis Analysis of Cantilever Wall and Sheet Pile as River Cliff Reinforcement Methods, American Journal of Engineering Research (AJER), vol.7, no.12, pp.190-194.
[20]    Wijayanthi, Shanty. 2005. Faktor-faktor Penyebab Keterlambatan Waktu Pembangunan Proyek Gedung Negara di Lingkungan Pemerintah Kota Kediri. Sepuluh Nopember Institute of Technology, Surabaya.


Scope Database

Our IAEME Publication journals are indexed in various indexing search engines

Aim and Scope
     International Journal of Construction Engineering (IJCE) is a peer-reviewed, open access journal that publishes original research articles and review articles in all areas of Construction engineering. The Journal is a peer-reviewed journal, aims to provide the most complete and reliable source of information on recent developments in Construction engineering. The journal provides a forum for the International Civil and Construction Engineering Community to present and discuss matters of major interest e.g. new developments in civil regulation.

Editorial Board

Dr. P.Muthupriya - Professor and Head, Department of Civil Engineering, Dr. N.G.P. Institute of Technology, Coimbatore, India, Email:

Dr. Mahdi Hosseini - Research Scientist, Department of Civil Engineering, Jawaharlal Nehru Technological University Hyderabad, India, Email:

Prof. Anuj Chandiwala - Assistant Professor, Department of Soil Mechanics & Foundation Engineering, Chhotubhai Gopalbhai Institute of Technology Gujarat, India, Email:

Dr. S.Bhagavathi Perumal - Professor, Department of Civil Engineering, R.M.K. College of Engineering and Technology, Tamilnadu, India, Email:,

Dr. Taha Ibrahim - Associate Professor, Department of Civil Engineering, Benha University, Egypt, Email:

Dr. Najm alghazali - Professor, Civil Engineering Department, Babylon University, Iraq, Email:,

Dr. Ali Akbar Firoozi - Professor, Department of Civil Engineering, University Kebangsaan, Malaysia, Email:

For Authors

Manuscripts should be submitted by one of the authors of the manuscript through the online manuscript submission system. Submissions by anyone other than one of the authors will not be accepted.
Regardless of the source of the word-processing tool, only electronic PDF or MS-Word files can be submitted through the online submission system. If for some technical reason online submission is not successful, the author can submit the manuscript to

Paper title (14 Bold)- Capital Letter

First Author1, Second Author2 (13 Bold- Times New Roman)

1(Department, College/ University Name, Address, Country Name, Email) (12)

2(Department, College/ University Name, Address, Country Name, Email) (12)

ABSTRACT (12 Bold)

The abstract should summarize the content of the paper. Try to keep the abstract below 350 words. Do not make references nor display equations in the abstract. The journal will be printed from the same-sized copy prepared by you. Your manuscript should be printed on A4 paper (21.0 cm x 29.7 cm). It is imperative that the margins and style described below be adhered to carefully. This will enable us to keep uniformity in the final printed copies of the Journal. Please keep in mind that the manuscript you prepare will be photographed and printed as it is received. Readability of copy is of paramount importance.(12)

Keywords (12 Bold) : About five key words in alphabetical order, separated by comma (12)


The introduction of the paper should explain the nature of the problem, previous work, purpose, and the contribution of the paper. The contents of each section may be provided to understand easily about the paper. (12)


The headings and subheadings, starting with "1. Introduction", appear in upper and lower case letters and should be set in bold and aligned flush left. All headings from the Introduction to Acknowledgements are numbered sequentially using 1, 2, 3, etc. Subheadings are numbered 1.1, 1.2, etc. If a subsection must be further divided, the numbers 1.1.1, 1.1.2, etc.

The font size for heading is 12 points bold face and subsections with 12 points and not bold. Do not underline any of the headings, or add dashes, colons, etc. (12)


The first paragraph under each heading or subheading should be flush left, and subsequent paragraphs should have a five-space indentation. A colon is inserted before an equation is presented, but there is no punctuation following the equation. All equations are numbered and referred to in the text solely by a number enclosed in a round bracket (i.e., (3) reads as "equation 3"). Ensure that any miscellaneous numbering system you use in your paper cannot be confused with a reference [4] or an equation (3) designation. (12)


To ensure a high-quality product, diagrams and lettering MUST be either computerdrafted or drawn using India ink.

Figure captions appear below the figure, are flush left, and are in lower case letters.When referring to a figure in the body of the text, the abbreviation "Fig." is used. Figures should be numbered in the order they appear in the text.

Table captions appear centered above the table in upper and lower case letters. When referring to a table in the text, no abbreviation is used and "Table" is capitalized. (12). Figures and tables should be included in the running text itself


A conclusion section must be included and should indicate clearly the advantages, limitations, and possible applications of the paper. Although a conclusion may review the main points of the paper, do not replicate the abstract as the conclusion. A conclusion might elaborate on the importance of the work or suggest applications and extentions. (12)


An acknowledgement section may be presented after the conclusion, if desired.( 12)


This heading is not assigned a number.

A reference list MUST be included using the following information as a guide. Only cited text references are included. Each reference is referred to in the text by a number enclosed in a square bracket (i.e., [3]). References must be numbered and ordered according to where they are first mentioned in the paper, NOT alphabetically.

Examples follow:

ournal Papers:

[1] M Ozaki, Y. Adachi, Y. Iwahori, and N. Ishii, Application of fuzzy theory to writer recognition of Chinese characters, International Journal of Modelling and Simulation, 18(2), 1998, 112-116. (12)


[2] R.E. Moore, Interval analysis (Englewood Cliffs, NJ: Prentice-Hall, 1966). (12) Note that the title of the book is in lower case letters and italicized. There is no comma following the title. Place of publication and publisher are given.

Chapters in Books:

[3] P.O. Bishop, Neurophysiology of binocular vision, in J.Houseman (Ed.), Handbook of physiology, 4 (New York: Springer-Verlag, 1970) 342-366. (12) Note that the place of publication, publisher, and year of publication are enclosed in brackets. Editor of book is listed before book title.


[4] D.S. Chan, Theory and implementation of multidimensional discrete systems for signal processing, doctoral diss., Massachusetts Institute of Technology, Cambridge, MA, 1978. (12)

Proceedings Papers:

[5] W.J. Book, Modelling design and control of flexible manipulator arms: A tutorial review, Proc. 29th IEEE Conf. on Decision and Control, San Francisco, CA, 1990, 500-506 (12)

Manuscripts not adhering to journal guidelines will be returned to authors without scientific evaluation. Submitted manuscripts adhering to journal guidelines are reviewed by the Editor-in-Chief or an Editor, who will assign them to reviewers. The review process is double blind. The Editor prepares a decision letter according to the comments of the reviewers, which is sent to the corresponding author. All non-reviewed manuscripts are sent back within 10 days and the decision letters of manuscripts are sent within 4 weeks.
Open Access authors retain the copyrights of their papers, and all open access articles are distributed under the terms of the Creative Commons Attribution License, CC BY (or the Creative Commons Attribution-NonCommercial License CC BY-NC), which allows users to (noncommercially) copy, use, distribute, transmit and display the work publicly and to make and distribute derivative works, in any digital medium for any responsible purpose, subject to proper attribution of authorship.
The use of general descriptive names, trade names, trademarks, and so forth in this publication, even if not specifically identified, does not imply that these names are not protected by the relevant laws and regulations.
While the advice and information in this journal are believed to be true and accurate on the date of its going to press, neither the authors, the editors, nor the publisher can accept any legal responsibility for any errors or omissions that may be made. The publisher makes no warranty, express or implied, with respect to the material contained herein.
IAEME Publication is committed to maintaining high standards through a rigorous peer-review together with strict ethical policies. Any infringements of professional ethical codes, such as plagiarism, fraudulent use of data, bogus claims of authorship, should be taken very seriously by the editors with zero tolerance..
IAEME Publication follows the Code of Conduct of the Committee on Publication Ethics (COPE), and follows the COPE Flowcharts for Resolving Cases of Suspected Misconduct.
Please find more general information for authors on the page: Information for Authors.

IAEME Publication Fees

IAEME Publication charges an Article Processing Charge (APC) once an article is accepted for publication. These charges cover the costs of turning a manuscript into a finished article, as well as the costs of hosting, distributing and promoting an article.

Article Processing Charges explained

We are committed to making the costs of publishing as clear as possible and so the charges for each journal are clearly displayed on each journal`s homepage.

When a manuscript is submitted, it passes through the many different departments at Hindawi to ensure the quality checks, peer review, production and promotion of articles is carried out in a timely manner and to a high standard:

✔ The Editorial Screening team, who perform initial technical and ethical checks

✔ The Editorial team, who help the journal`s Academic Editors manage the review process

✔ The Production team, who convert the manuscript to a professionally typeset article and well-structured file format

✔ The Proofing team, who coordinate the proofing process through Hindawi`s Online Proofing System (OPS)

✔ The Editorial Quality Assurance team, who perform a final check to ensure that the manuscript and its review process adhere to the journal`s guidelines and policies

✔ Our Marketing and Communication teams, who ensure your article receives the attention it deserves.

✔ The Technology team, who build and maintain our systems, and develop new systems

The work these teams do contribute to the requirement of an APC and is why the actual amount payable varies depending on the journal in which you wish to publish your article.

IAEME Publication does not request Article Submission Charges, also called Submission Fees. These are due at the time of submission of the manuscript. Nor does IAEME charge per page or for color figures or for any other items for which other publishers are known to charge.

Sources for Article Processing Charges (APC)

Authors of an article are responsible for arranging the payment of APC. Still, that typically does not mean that authors end up paying for the publication of the article. The cost of APC is very often assumed either by the organization funding the research published in the article, or by an Open Access Publishing Fund, or by the institution at which the author is employed.

Fair Dealing - Authors and Publisher

When an author submits a manuscript for review at one of IAEME`s journals, the submitted manuscript should not have been previously published in any form and must not be currently under consideration for publication elsewhere. The manuscript should also not be submitted to any other journal during the review process at IAEME Publication. In case the review process at IAEME takes much longer than stated and the author wishes to end the review process at IAEME, he/she should get in contact with the Editorial Assistant of the journal at IAEME and come to an agreement suitable for both sides after looking at the stage of the manuscript in the review process.

With the APC specified above, the author is given an indication what the APC will be. IAEME is charging Publication Fees (APC) but not Submission Fees. This is to the benefit to authors because payments are only due once the author knows the manuscript is accepted. IAEME with editors and reviewers puts much effort in dealing with the manuscript and expects the authors to stick to the common plan of publishing the paper which is linked to payments of APC as given above at the end of the review process. The author is not legally bound at this time, but it would be seen as a strong breach of academic conduct to back off from the publication process. Once the manuscript is accepted for publication, IAEME will issue an invoice in the Paper Submission and Manuscript Tracking System. This is IAEME `s legal offer and will state the regular APC of the journal. The Corresponding Author is expected to arrange payments of the amount stated at this time. In severe cases IAEME `s Complaints Procedure can be followed and the result of this should be binding to the author.

Refund Policy

Once an article has been accepted for publication, any Article Processing Charges on the article become due. The submitting author accepts responsibility for the Article Processing Charges, and will not issue refunds of any kind except those payments made by mistake or in excess of the amount required.

Subject Area
The topics to be covered by this journal include but are not limited to the following fields:
• Construction Material Handling
• Concrete Mix Design
• Equipment
• Safety Engineering
• Materials Procurement
• Production Planning
• Specifications
• Scheduling
• Estimating
• Cost Control
• Quality Control
• Labor Productivity
• Contract Administration
• Construction Management
• Computer Applications
• Environmental Concerns
• Design of Temporary Structures
• Quality Assurance and Quality Control
• Building and Site Layout Surveys
• On Site Material Testing
• Budgeting & Cost Engineering
• Planning and Management
• Construction of Structures

Create Account

Log In Your Account